Myalarm Genesys 824 Alpha Especificaciones descargar pdf (Pagina 7)

3440-0241 Rev G

58 C PGM 2 Cutoff

(2 Digit Entry)

This output will stay energized for the amount of time

programmed in this memory location after an alarm circuit trips

and it has been programmed to energize the PGM 2 output,

Value 00 - 99 minutes, Default: 0 minutes.

NOTE

: A value of 00 will keep PGM 1 and PGM 2 output

energized until a valid PIN is entered.

Memory Location 59 & 59B

PGM OUTPUT OPTION

59 PGM 1 Output Option

(2 Digit Entry) PGM 1 Output can

be programmed to be used as

one

of the following functions:

The current available for this output is 20mA.

00 - Alarm Output

- This option must be enabled when

used as a Zone Alarm Output. Output time follows value in

location 58 B.

01 - System Status

- If this option is selected PGM 1

output will be present when all zones are secured When

the system has been armed this output will not be present.

02 - Ground Start

- Can be used for a phone system that

requires a ground to be produced on either tip or ring to

bring up a dial tone. This output will be present for 2

seconds.

NOTE:

Additional hardware is required, see page 14 for

wiring diagram.

03 - Fail to Communicate

- Can be used when the dialing

attempts have been exhausted that is programmed in

memory location 53 B. After the last dial attempt, this

output will be present.

04 - Follow Entry - Exit Delay

- When this option is

selected, this output will be present for the amount of time

programmed in entry exit delay times

(see memory location 57).

05 - PGM 1 Output with Utility PIN

- When this option is

selected, you must also program the utility PIN in the user

program in memory location 2. When the utility PIN is

activated this output will be present for five seconds.

06 - Long Range Radio Output

- When this option is

selected, the audio data signal for

Varitech

(only) long

range radio transmission will be present at this output.

07 - Partition One Status

- This option allows the PGM-1

output to be utilized as an armed status indicator for

partition one.

Value 00-99Default: 99 (Disabled

)

NOTE:

08-99 Disables this Option

59 A PGM 2 Output Option

(2 Digit Entry) PGM 2 Output

can be programmed to be used as

one

of the following

functions: The current available for this output is 20mA.

00 - Alarm Output

- Is used in conjunction with Zone

Output. Output value follows time in location 58 B.

01 - System Armed Status

- When this option is selected,

this output will be present when the exit time has expired

and will remain until the system is disarmed.

02 - Not Used

- for future use.

03 - Fail to Communicate

- Can be used when the dialing

attempts have been exhausted that is programmed in

memory location 53 B. After the last dial attempt, this

output will be present until communication is restored.

04 - Follow Entry - Exit Delay

- When this option is

selected, this output will be present for the amount of time

programmed in entry exit delay times

(see memory location 57).

05 - PGM 2 Output with Utility PIN

- When this option is

selected you must also program the utility PIN in the user

program in memory location 2. When the utility PIN is

activated this output will be present for five seconds.

06 - Radio Key Output for Long Range Radio

.- When

this option is selected , the Varitech radio key will be

produced.

07 - Ring Back

- When this option is selected this output

will be activated for two seconds after the open and close

report has been acknowledged. (See memory location 60)

08 - Partition Two Status

- This option allows PGM-2

output to be utilized as an armed status indicator for

partition two.

Value 00 – 99 Default: 99 (Disabled

)

NOTE

: 09-99 Disables this Output

59B - PGM Output Options

Requires depressing the number

that corresponds to the option that you wish to enable and the

number will be displayed on the LCD. Depressing a number

that previously was displayed will remove the number from the

LCD and disable the option.

OPTION

1 = PGM-1 on Two Wire Smoke Loop

2 = PGM-2 on Two Wire Smoke Loop

3 = PGM-1 on Keypad Fire

4 = PGM-2 on Keypad Fire

5 = PGM-1 on Keypad Panic

6 = PGM-2 on Keypad Panic

7 = PGM-1 on Keypad Emergency

8 = PGM-2 on keypad Emergency

1 - PGM-1 on Two Wire Smokes

- This option allows

PGM-1 to energize when the two wire smoke loop detects

an activation . This output will stay active for the period of

time programmed in memory 58B or when a users PIN is

entered.

2 - PGM-2 on Two Wire Smokes

- This option allows

PGM-2 to energize when the two wire smoke loop detects

an alarm activation . This output will stay active for the

period of time programmed in memory location 58C or

when a users PIN is entered.

1 2 3 4 5 6 7 8 9 10 11 12 ... 21 22

Comentarios a estos manuales

Sin comentarios

Myalarm Genesys 824 Alpha Especificaciones Pagina 7

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad Myalarm Genesys 824 Alpha