Myalarm Genesys 824 Alpha Especificaciones descargar pdf (Pagina 13)

3440-0241 Rev G

78 A Duress PIN

(4 Digit Entry)

This PIN will arm or disarm the system and will transmit the

duress report code (see memory location 68B) to the central

station.

Value 0000 - 9999, Default: BLANK.

NOTE

: PIN's (installer, duress, user) cannot be duplicated.

If a duplicate PIN is attempted to be programmed

an audible from the keypad will indicate the PIN

has been rejected.

79 - 79 A Battery Charging Calculations

BATTERY CALCULATIONS

To comply with UL requirements the primary power failure

trouble signal for the communicator shall not be

transmitted until the standby power capacity is at least 25

percent depleted, but not more than 50 percent.

Therefore, it is necessary to program these two memory

locations with the total current available (subtract total

current draw of panel, keypad(s), expansion modules and

other auxiliary devices powered from auxiliary power from

total current capacity) and amp-hour rating of battery to be

used.

79) 1000 mA - Total current in mA

10 = XX

Convert XX in Hex Chart 1 and enter in 79.

79 A) AH Batt x 10 = YY

Convert YY in Hex Chart 1 and enter in 79 A.

NOTE 1:

LOW BATTERY CODE is transmitted when:

1) there is no battery connected;

2) the battery fuse is open;

3) the battery voltage goes below approximately

11.5 VDC.

NOTE 2:

GOOD BATTERY is transmitted when the battery

voltage reaches approximately 12 VDC.

79B First 2 digits of Panel Access ID for RPU

(Remote Programming Utility)

79C Last 2 digits of Panel Access ID for RPU

Memory Location

80 - 95

NOT USED / FUTURE USE

ALPHA PROGRAMMING INSTRUCTION

The alpha programming of the control panel is accessed by

entering the

installers PIN

(

↑

↑↑

↑

) 7

(AWAY)

. The LCD will

change to:

ENTER ZONE #

The zone number you wish to program should be entered as

two digits (o1-24). Pressing the

(

↑

↑↑

↑

)

will lock in your selection

and the LCD will change to read:

ENTER ZONE #

ZONE ONE

(ZONE ONE was used only as an example)

At this point you may now begin entering the alpha text you

wish by selecting the number that corresponds to the letter or

character from the chart on page. You must press

(

↑

↑↑

↑

)

after

each of your selections to lock in the letter and this will

automatically advance the cursor to the next character. Once

editing of the zone name have been completed, you

must

press

(INST)

to lock your selection into memory. If

(INST)

is not

pressed, the name will revert to the factory default: settings.

After

(INST)

is pressed, the LCD will now request another zone

number be entered. Repeat the above procedure until all zones

have been named.

Once all zones have been named, press

(#)

once to return to

the main installers program mode. Pressing the

(#)

a second

time will return the User's operating mode.

PROGRAMMING HINTS

1)To enter a space, simply press the

(

↑

↑↑

↑

)

. The cursor will delete

the previous character (if anything) and advance to the next

character.

2) To move about the location without deleting the characters,

press

(AWAY)

to move right or press

(STAY)

to move left.

WIRING INSTRUCTIONS

TERMINALS

1 & 2 16 VAC Class II plug-in transformer (20 VA

maximum). Use 18 GA twisted or zip pair and keep

wire run as short as possible. Test the electrical

outlet being used to ensure it is not controlled by a

light switch. (24 hour source)

3-4-5-6 Data bus inputs - These terminals are used for

wiring in keypads (maximum 4), expansion modules

(maximum 2), and G-FM3. The keypads and

expansion modules can be wired in either a daisy

chain or homerun configuration. Each keypad must

be addressed by setting the two dip switches

located on the back of each keypad. Maximum

cable length 1,000 feet.

1 2 ... 8 9 10 11 12 13 14 15 16 17 18 ... 21 22

Comentarios a estos manuales

Sin comentarios

Myalarm Genesys 824 Alpha Especificaciones Pagina 13

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad Myalarm Genesys 824 Alpha