Myalarm Genesys 824 Alpha Especificaciones descargar pdf (Pagina 11)

3440-0241 Rev G

on the Buss for the amount of time programmed in memory

location 58A or until a valid PIN is entered in the keypad

Default: NO

3 - Digital first & Radio second

With this option selected

the digital signal will be transmitted first and if it is

successful, the radio signal will not be sent.

Default: NO

4 - G-FM3 Installed

With this option selected the panel will

recognize the G-FM3 (Fire Module) installed and will

indicate a bus fault should the G-FM3 fail or be removed

from the system

. Default: NO

5 - 50 Hz or 60 Hz

This option is very important to be set

correctly to insure proper operation of the time clock. The

default is set for US operation (60Hz). To set the system

for 50Hz, the number 5 should be showing on the LCD.

Default: 60 Hz

6 - Telco Fault Monitoring Enable

With this option

selected, the keypad will give a visual indication of a

telephone trouble (TLM) and emit a pulsing audible tone

from keypad.

Default: NO

7 - System Test to be Reported on Telco

With this option

selected the panel will automatically transmit the signal to

the central station on the telco line.

Default: YES

8 - Partition System

With this option selected the panel

can be used as two separate systems. The first half of the

zones will automatically become partition number 1 and

the second half of the zones will become partition number

2. PIN's one through eight automatically become assigned

to partition number one and PIN's nine through sixteen will

become assigned to partition number two. Partition

number one will always report its information to Receiver

number one including open and close signals and partition

number two will always report its information to receiver

number two including open and close signals. The house

keeping signals (AC fail, low batt., etc.) report to receiver

one. (See memory location 48 through 53.)

Default: NO

76 A System Features

(Multiple Entries) Requires depressing

the number that corresponds to the option that you wish to

enable and will be displayed on the LCD. Depressing a number

that previously was displayed will remove the number from the

LCD and disable the option.

OPTIONS

1 = Keypad Panic Enabled

2 = Keypad Panic Audible

3 = Keypad Fire Enabled

4 = Keypad Fire Audible

5 = Keypad Emergency Enabled

6 = Keypad Emergency Audible

7 = Key switch or Tamper Inputs

8 = AC fail Audible on Keypad

1 - Keypad Panic Enabled

With this option selected the

keypad panic function is enabled ("AWAY" and "3"). You

may have this function set for silent or audible or both.

Default: NO

2 - Keypad Panic Audible

with this option enabled, the

keypad panic will be audible.

Default: NO

silent only = report code (see memory location 71A).

bell only = no report code + panic audible (see below)

report+bell = report code(see memory location 71A)+

Panic audible (see below)

3 - Keypad Fire Enabled

with this option selected the

keypad fire function is enabled ("STAY" and "6"). You may

have this function set for silent or audible or both.

Default: NO

4 - Keypad Fire Audible

with this option enabled, the

keypad fire will be audible

. Default: NO

silent only = report code (see memory location 70C).

bell only = no report code + fire audible (see below)

report+bell = report code(see memory location 70C)+

Fire audible (see below)

5 - Keypad Emergency Enable

with this option selected

the keypad emergency function is enabled ("INSTANT"

and "9".). You may have this function set for silent or

audible or both

. Default: NO

6 - Keypad Emergency Audible

with this option enabled,

the keypad emergency will be audible

. Default: NO

silent only = report code (see memory location 71).

bell only = no report code + emer. audible (see below)

report+bell = report code(see memory location 71)+

emergency audible (see below)

7 - Key switch or Tamper Inputs

When the key switch

option is selected terminals 7 and 10 will support any

momentary or latching arming station. The number 7

should be displayed on the LCD to select the key switch

input. The number 7 should not be displayed if you need to

use as a tamper switch. A report code must be

programmed in memory location 69C when selected for

tamper switch input, This tamper input is silent only.

Default: Tamper Switch

8 - AC Fail Audible on Keypad

Should there be a loss of

AC power, this option will enable an audible tone to emit

from all keypads, together with AC trouble display on the

LCD. Only AC trouble will display on the LCD if this option

is not selected.

Default: NO

76 B Monitor Mode Features

(Multiple Entries)

Requires depressing the number that corresponds to the option

that you wish to enable and the number will be displayed on the

LCD. Depressing a number that previously was displayed will

remove the number from the LCD and disable the option.

(See next page).

1 2 ... 6 7 8 9 10 11 12 13 14 15 16 ... 21 22

Comentarios a estos manuales

Sin comentarios

Myalarm Genesys 824 Alpha Especificaciones Pagina 11

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad Myalarm Genesys 824 Alpha