Myalarm Genesys 824 Alpha Especificaciones descargar pdf (Pagina 10)

3440-0241 Rev G

TOTAL SYSTEM DIGIT TO ENTER

CURRENT (mA) IN LOCATION

73C

00 - 100mA 91

101 - 200mA 92

201 - 300mA 93

301 - 400mA 94

401 - 500mA 95

501 - 600mA 96

601 - 700mA 97

701 - 800mA 98

801 - 900mA 99

74 Abnormal Self Test Report Code

(2 Digit Entry)

This communicator test report code will be transmitted in place

of the self test code programmed in memory location 77C

should a fire zone or the two wire smoke detector loop be left in

an alarm or trouble condition .

NOTE:

This must be used to comply with UL864.

74A Telephone (TLM) Fault report code (2 Digit Entry)

This code will be sent whenever a telephone line fault is

detected. (See also memory location 76-6)

Value 00 - FF.Default: 00 (Disabled)

Memory Location 75 - 75C

SIGNAL ROUTING

75 Receiver Reporting for Alarm & Restores - Open &

(2 Digit Entry)

If you have been assigned to only one telephone number and

account number, duplicate the receiver information and select

option 2 for memory locations 75 and 75A.

The first digit tells the panel which receiver or receivers to direct

the alarm and restore report codes.

Value 0 - 4, Default: 0.

Value Function

0 Report only to receiver number 1

1 Report only to receiver number 2

2 Report first to receiver number 1, If not successful,

attempt to report to receiver number 2

3-4 Report to receiver number 1 and receiver number 2

The second digit tells the panel which receiver or receivers to

direct the open and close report code to.

Value 0 - 4, Default: 0.

Value Function

0 Report only to receiver number 1

1 Report only to receiver number 2

2 Report first to receiver number 1, if not successful,

attempt to report to receiver number 2

3 Report to receiver number 1 and receiver number 2

4 No reporting for receiver number 1 or number 2

75 A System Report Code

(2 Digit Entry)

The first digit tells the panel which receiver or receivers to direct

the housekeeping signals (power codes, failure codes, keypad

triggered alarm codes, etc.).

Value 0 - 9, Default: 0.

Value Function

0 Report only to receiver number 1

1 Report only to receiver number 2

2 Report first to receiver number 1, if not successful,

attempt to report to receiver number 2

3 Report to receiver number 1 and receiver number 2

4 No Telco reporting for System messages

Value 0 - 4 Default: 0

The second digit selects reporting of codes on Long-range

radio.

Value Function

0 No radio out put for open/close, system test, or

system messages

1 open/close on radio

2 system test code on radio

3 open/close + system test codes on radio

4 system messages on radio

5 system message + open/close on radio

6 system message + system test on radio

7 system message + system test + open/close on

radio

Value 0 - 7 Default: 0

75 B Communication Fail Report Code

(2 Digit Entry)

The Communication Fail Report Code is transmitted when the

panel has exhausted its dialing attempts

(see memory location 53B).

Value 01 - FF, Default: 00 (Disabled).

Note

Must use "Two phone lines" or "One phone line and

Long range radio".

75 C Number of Radio Attempts

The number of times the event is transmitted via

Varitech

long

range radio.

Value 00 - 09 units Default: 00 (Disabled)

Memory Location 76 - 79C

SYSTEM FEATURES

76 System Features

(Multiple Entries) requires depressing

the number that corresponds to the option that you wish to

enable and the number will be displayed on the LCD.

Depressing a number that previously was displayed will remove

the number from the LCD and disable the option.

Shows Default condition : All OFF

OPTIONS

1 = Bell Test

2 = Bell Audible on Bus Fault

3 = Digital first & Radio second

4 = G-FM3 Installed

5 = 50 Hz

6 = Telephone Fault(TLm)Monitoring enable

7 = System test to be reported on Telco

8 = Partition System

1 - Bell Test

With this option selected, the bell voltage will

be present for three seconds when the control panel is

armed.

Default: NO

2 - Bell Audible on Bus Fault

With this option selected

the bell voltage will energize should the panel detect a fault

1 2 ... 5 6 7 8 9 10 11 12 13 14 15 ... 21 22

Comentarios a estos manuales

Sin comentarios

Myalarm Genesys 824 Alpha Especificaciones Pagina 10

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad Myalarm Genesys 824 Alpha